HHE 2022-2023

623 Twelve New STRAIGHT COUPLING PART NUMBER TUBE OD PRICE JGSBA0110 10 mm £9.41 JGSBA0115 15 mm £9.97 JGSBA0122 22 mm £13.75 JGSBA0128 28 mm £21.12 New REDUCING COUPLING PART NUMBER TUBE OD TUBE OD PRICE JGSBA011510 15 mm 10 mm £14.14 JGSBA012215 22 mm 15 mm £18.46 JGSBA012822 28 mm 22 mm £23.19 New SLIP COUPLING PART NUMBER TUBE OD PRICE JGSBA01S15 15 mm £14.48 JGSBA01S22 22 mm £19.19 JGSBA01S28 28 mm £22.41 New 45° ELBOW PART NUMBER TUBE OD PRICE JGSBA0515 15 mm £11.12 JGSBA0522 22 mm £15.35 JGSBA0528 28 mm £18.04 2150 2150 2150 2150 STANDARD FITTINGS UXL FITTINGS New STRAIGHT COUPLING PART NUMBER TUBE OD PRICE JGSBA0135E 35 mm £18.60 JGSBA0142E 42 mm £23.92 JGSBA0154E 54 mm £35.63 New REDUCING COUPLING PART NUMBER TUBE OD TUBE OD PRICE JGSBA013528E 35 mm 28 mm £27.79 JGSBA014235E 42 mm 35 mm £31.23 JGSBA015442E 54 mm 42 mm £33.72 New SLIP COUPLING PART NUMBER TUBE OD PRICE JGSBA01S35E 35 mm £32.44 JGSBA01S42E 42 mm £42.10 JGSBA01S54E 54 mm £63.47 New 45° ELBOW PART NUMBER TUBE OD PRICE JGSBA0535E 35 mm £22.55 JGSBA0542E 42 mm £29.89 JGSBA0554E 54 mm £39.44 2150 2150 2150 2150 CONNECTING PUSH-FIT Cutting the pipe Cut the pipe square using a rotary pipe cutter and then debur using a SharkBite Depth/Deburring tool. There should be no burrs or sharp edges on the pipe end as this can damage the O-Ring during pipe insertion. Measure the depth Using the appropriate Depth Marker Demounting Clip or tape measure, mark the insertion depth onto the pipe. Making the connection Align the pipe squarely with the fitting de-mounting ring and push the pipe into the fitting with a slight twist until the pipe reaches the pipe stop. If using plastic pipe, use a liner if specified by the pipe manufacturer. Demounting 10-28 mm with clip Holding the fitting in the palm of the hand, snap the demounting clip over the pipe, with the SharkBite logo away from the fitting. Slide the clip up to the demounting ring and press firmly on the two ‘finger pads’, while simultaneously twisting and pulling the pipe to release. Demounting 10-28 mm with tongs Position the tongs over the fitting and pipe with the SharkBite logo facing away from the fitting. Squeeze the tongs together, while gripping the pipe in the other hand, simultaneously twist and pull the pipe to remove, if necessary. Use the thumb as a lever to assist release. Demounting 35-54 mm UXL Snap the demounting clip over the pipe and locate the clip slots over the two studs in the end cap. Rotate the clip clockwise by 10° until it locks, then twist and pull the pipe from the fitting. DEMOUNTING PUSH-FIT Note: SharkBite fittings utilise a PTFE coated O-Ring. This coating is semi-permanent and multiple pipe insertions/de-mountings will remove this coating, making pipe insertion harder. AIR & PNEUMATIC BRASS FITTINGS MAKING A CONNECTION