HHE 2022-2023

686 Thirteen 9000 SERIES TEE TUBE TO TUBE PART NUMBER TUBE OD PRICE A9200-04 4 mm £4.56 A9200-06 6 mm £4.94 A9200-08 8 mm £5.87 A9200-10 10 mm £9.66 A9200-12 12 mm £12.52 A9200-14 14 mm £19.84 A9200-15 15 mm £19.51 A9200-16 16 mm £24.06 A9200-18 18 mm £29.26 9000 SERIES OFF SET LEG TEE BSPT MALE PART NUMBER TUBE OD THREAD PRICE A9230-0418 4 mm 1/8” BSPT £3.67 A9230-0618 6 mm 1/8” BSPT £3.89 A9230-0614 6 mm 1/4” BSPT £4.20 A9230-0818 8 mm 1/8” BSPT £4.60 A9230-0814 8 mm 1/4” BSPT £4.65 A9230-0838 8 mm 3/8” BSPT £5.72 A9230-1014 10 mm 1/4” BSPT £7.70 A9230-1038 10 mm 3/8” BSPT £7.73 A9230-1238 12 mm 3/8” BSPT £10.21 A9230-1212 12 mm 1/2” BSPT £10.21 A9230-1412 14 mm 1/2” BSPT £15.76 A9230-1512 15 mm 1/2” BSPT £15.76 A9230-1612 16 mm 1/2” BSPT £19.77 A9230-1812 18 mm 1/2” BSPT £24.09 9000 SERIES CENTRE LEG TEE BSPT MALE PART NUMBER TUBE OD THREAD PRICE A9220-0418 4 mm 1/8” BSPT £3.67 A9220-0618 6 mm 1/8” BSPT £3.89 A9220-0614 6 mm 1/4” BSPT £4.20 A9220-0818 8 mm 1/8” BSPT £4.60 A9220-0814 8 mm 1/4” BSPT £4.65 A9220-0838 8 mm 3/8” BSPT £5.72 A9220-1014 10 mm 1/4” BSPT £7.70 A9220-1038 10 mm 3/8” BSPT £8.75 A9220-1238 12 mm 3/8” BSPT £10.21 A9220-1212 12 mm 1/2” BSPT £10.21 A9220-1412 14 mm 1/2” BSPT £15.76 A9220-1512 15 mm 1/2” BSPT £15.76 A9220-1612 16 mm 1/2” BSPT £18.84 A9220-1812 18 mm 1/2” BSPT £24.09 9000 SERIES ELBOW TUBE TO TUBE PART NUMBER TUBE OD PRICE A9260-04 4 mm £3.29 A9260-06 6 mm £3.60 A9260-08 8 mm £4.22 A9260-10 10 mm £6.75 A9260-12 12 mm £8.99 A9260-14 14 mm £13.88 A9260-15 15 mm £13.88 A9260-16 16 mm £17.17 A9260-18 18 mm £20.73 1460 1460 1460 1460 UNIVERSAL COMPRESSION FITTINGS SIZE MAX. PRESSURE ADVISED 9000 SERIES 13000 SERIES Ø 4 130 kg/cm 3 128.6 bar 150 kg/cm 3 148.4 bar Ø 6 180 kg/cm 3 178.1 bar 150 kg/cm 3 148.4 bar Ø 8 150 kg/cm 3 148.4 bar 135 kg/cm 3 133.6 bar Ø 10 115 kg/cm 3 113.8 bar 95 kg/cm 3 94.0 bar Ø 12 75 kg/cm 3 72.4 bar 75 kg/cm 3 74.2 bar Ø 14 70 kg/cm 3 69.3 bar 100 kg/cm 3 99.0 bar Ø 15 70 kg/cm 3 69.3 bar 95 kg/cm 3 94.0 bar Ø 16 70 kg/cm 3 69.3 bar 95 kg/cm 3 94.0 bar Ø 18 65 kg/cm 3 64.3 bar 70 kg/cm 3 69.3 bar Ø 22 - - 70 kg/cm 3 69.3 bar DESCRIPTION The working pressures and working temperatures depend on which type of tube is used. For this reason, the values must be determined in accordance with the tube’s features. The values below are the maximum pressures advised for the fittings at a temperature of 20°C connected to copper tube, which has a thickness of 1 mm. Working pressures stated have been obtained from a test using a Safety Factor 4. THREADS Tapered gas in conformity with ISO 7.1, BS 21, DIN 2999. Parallel gas in conformity with ISO 228. Metric in conformity with ISO R/262. FLUIDS Water, oils, compressed air, fluids in general for the hydraulic, pneumatic & oil dynamic plants, etc. CONNECTION TUBES Tubes made in copper, steel, iron, aluminium, brass, etc. With an inside support bush, may also be used for plastic material, such as Rilsan PA 11, nylon PA 6, etc. ASSEMBLY INSTRUCTIONS To ensure the best results using these fittings, please follow the instructions listed. 1 . Cut the tube at 90° and remove internal and external burrs. 2 . Lightly oil the tube nut, olive and fitting thread. Slide the nut and olive onto the tube, ensuring that the sharp side of the olive is facing the fitting. 3 . Screw the nut onto the fitting by hand until hand-tight. 4 . Ensure that the tube is pushed fully home into the fitting before tightening the nut with the correct spanner. 5. Tighten nut with the spanner one and a quarter turns, marking reference points if necessary. 6 . To ensure that the olive has gripped the tube correctly, unscrew the nut and make sure that the groove made by the olive is even. 7. Tighten the nut again with an extra quarter turn. When fitting to curved tubes, ensure that the section entering the fitting is straight for a minimum length of twice the nut height.